AcuRite 00607 Specifications Page 31
- Page / 224
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Southwestern Industries, Inc.
ProtoTRAK SMX K2, K3, K4 & Retrofit Safety, Installation, Maintenance, Service & Parts List Manual
26
Item
P/N
Title
Qty
2
22378
MANIFOLD-PT4 AIR
1
3
22607
FILTER/REGULATOR-PT4
1
8
22644-4
PLUG-1/4 NPT HEX SOCKET
3
9
22645-4
NIPPLE-1/4 NPT x 1.37 LG
1
11
22646-4
ADAPTOR-ELBOW MALE 1/4 x 1/8 NPT
1
12
22647-2
NIPPLE-1/8 NPT x 0.750" LG
1
18
4-40X3/8 31B
SCREW-PH-PHIL-EXT SEMS-STL-BO
2
19
10-32X3/8 10B
SCREW-PH-PHIL-STL-BO
2
20
M6-1.0X25 25B
SCREW-SHCS-STL-BO
2
24
22772
SOLENOID ASSY- AIR REGULATOR
1
25
22581-5
OILER
1
i22380-1
2.13 Mounting the Display Pendant
The ProtoTRAK SMX display pendant mounts to the pendant arm with four 1/4-20 x ¾ SHCS
that are shipped screwed into the left side of the display. There is a locating screw on the
pendant arm to help align the pendant with the mounting holes.
CAUTION!
The locating screw in the arm is used for positioning. Keep a hold of the pendant until the
screws are fastened.
If the pendant arm rotates too freely, remove the painted cap on the bracket attached to the
column and tighten the hex nut to adjust it. Replace the cap.
2.14 Cable Interconnections
All cable interconnections are made at the factory except for those connecting to the pendant
display. There are a total of 4 cables that need to be connected to the pendant for non-spindle
control machines. See Figure 15 & 16 for a complete illustration of cable interconnections for all
components. There are an additional 2 cables for the electronic handwheel option and 2 more
cables for the spindle control option (digital I/O and spindle control ports).
With the main power to the machine turned off, plug in the connectors that are bundled on the
pendant arm. Each cable mates to only one connector on the pendant display back panel. Use
the key on the pendant to match up the connectors with the correct port. The machine ID port
(or called LPT) and parallel port (hardware key) will have a key plugged into it. The monitor
port and network ports will be left empty during installation.
Make sure there is sufficient slack in the cables for when the pendant is rotated about the
pendant arm. The worst case is when the pendant is all the way forward toward the operator.
The following drawing describes all of the cable connections to the pendant.
Make sure there is a hardware (option) key plugged into the parallel port of the pendant. This
key activates any converters or options ordered. The part # for this key is 22648. The key
must be programmed according to the type of machine it is on and the options ordered.
Figure 12 - Air Regulator/Solenoid Assembly - P/N: 22380-1
- ProtoTRAK 1
- K2, K3, K4 & 1
- Retrofit 1
- Fax 310.764.2668 2
- Fax 310.886.8029 2
- Table of Contents 3
- 1.0 Safety 6
- 1.3 Safety Precautions 8
- 2.0 Installation 11
- 2.2 Uncrating 13
- 2.5 Machine Specifications 15
- 2.9 Cleaning 21
- Placement of Levels 22
- 2.11 Electrical Connection 23
- Not for retrofit 24
- Figure 8 24
- Figure 9 25
- Figure 9-1 26
- Figure 11 29
- Transformer Option Schematic 29
- 2.14 Cable Interconnections 31
- Figure 14 33
- Pendant - Right Side 33
- P/N: 24000-1 33
- Figure 15 34
- Cable Connection Diagram 34
- Non-Spindle Control 34
- Figure 16 36
- 2.15 Lubrication 37
- 2.15.2 Head Lubrication 39
- • X = 1.318 40
- • Y = 1.318 40
- Figure 18 41
- Euclid Block 41
- 3.1.1 Poor Finish 42
- 3.1.2 Circles Out of Round 43
- 3.2.1 Run Away Axis 45
- 3.2.2 Slow Down Axis 46
- 3.2.3 Axis Will Not Jog 46
- 3.2.5 Vibration in Motion 47
- 3.2.6 Searching Axis 48
- 3.3.1 Display Blanks 49
- 3.3.3 Keyboard Lockup 49
- 3.3.4 Fault X or Y 49
- 3.3.8 System Shuts Off 51
- Machines Only) 52
- Direction 56
- 3.5.4 Head Noise 59
- 4.0 Diagnostics 61
- 4.1.3 Lubrication 62
- 4.1.4 Machining Set-Up 62
- 4.1.4.1 Spindle Speeds 63
- 4.1.4.2 Feedrates 63
- 4.4 Motor Diagnostics 66
- 4.5 Servo Driver 67
- 4.6 Glass Scales 68
- 4.7 TRAK Sensors 69
- 4.8 Electrical 71
- 4.8.4 Cable Connections 72
- Figure 19 73
- Electrical Box Schematic 73
- Figure 20 75
- Figure 21 76
- LEDs on Spindle 76
- Control Board 76
- 4.9 Service Codes 77
- 4.9.1 Software Codes 77
- 4.9.2 Machine Set-up Codes 78
- 4.9.3 Diagnostic Codes 81
- & Maintenance 84
- Figure 22 85
- Figure 23 86
- Figure 24 88
- Flash Disk Replacement 88
- Flash Disk Parts List 88
- Flask Disk Replacement 88
- 5.1.6 TRAK Sensor 89
- Figure 25 90
- M5 Base Mounting 90
- Figure 26 91
- TRAK Sensor Mounting 91
- Figure 27 92
- K Mill Sensor Assembly 92
- Z-Axis Glass Scale Assembly 95
- Figure 29 96
- Glass Scale Alignment 96
- 5.1.8 Power Drawbar 97
- Figure 30 98
- Power Drawbar Assembly 98
- Figure 31 100
- X-Axis Drive Assembly 100
- Figure 33 105
- Spindle Motor Wiring 105
- Figure 36 107
- Figure 37 109
- Figure 38 110
- 5.2 Maintenance 111
- Figure 39 111
- Table Gib Adjustment 111
- Figure 40 112
- Table Gib Screw 112
- Figure 42 114
- Figure 43 115
- Calibration Set-Up 115
- 5.2.3.2 Tramming the Head 117
- Side-to-Side Alignment 117
- Back to Front Adjustment 118
- 5.2.4 Limit Switch Option 119
- 6.0 Retrofit Installation 121
- 7.0 Installation Procedures 123
- X-Axis Ball Screw 125
- Figure 51 127
- Figure 55 133
- Figure 56 136
- X Motor Mounting 136
- Figure 58 141
- Z-Axis Glass Scale Assembly 141
- Figure 59 142
- X Bracket Installation 142
- Figure 60 143
- Y Bracket Installation 143
- Figure 61 144
- 148
- 7.9 System Interconnection 150
- Figure 66 151
- Figure 68 156
- & Covers Assembly 156
- Figure 68-1 158
- Ball Screw Module 158
- P/N 24250 158
- Parts List Ball Screw Module 159
- 8.4 Lagun Z Axis Cutout 160
- Figure 69 160
- 9.2 Warranty 161
- 9.3 Replacements 163
- Figure 100 164
- Figure 104 169
- Pulley Pinion Sub-Assembly 169
- P/N: 20697-4 169
- Figure 105 170
- Lower Vari-Disc Sub-Assembly 170
- P/N: 20697-5 170
- Figure 106 172
- Upper Vari-Disc Sub-Assembly 172
- P/N: 20697-6 172
- Figure 109 176
- Bottom Housing Assembly 176
- Figure 110 180
- P/N: 20698-1 180
- Parts List 192
- Head Top Assembly - 24692 192
- Figure 120 194
- Hi-Low Shift Clutch 194
- Sub-Assembly 194
- P/N: 20778-2 194
- Figure 121 196
- Hi-Low Shift 196
- P/N: 20778-3 196
- Figure 125 202
- Speed Change Handwheel 202
- P/N: 20778-7 202
- Figure 127 204
- Lower Head Assembly 204
- Figure 128 208
- Worm Gear Cradle 208
- P/N: 20779-1 208
- Figure 134 214
- K2/K3 Base Machine P/N 20785 214
- Figure 135 218
- K4 Base Machine P/N 26900 218
- Parts List - K4 Base Machine 219
- Figure 136 221
- P/N: 23470-220 or 23470-440 221
- Figure 137 222
- P/N 23470-220 or 23470-440 222
- TRAK Warranty Policy 224
Related products and manuals for Weather stations AcuRite 00607
Weather stations AcuRite 614 User Manual
(457 pages)
(457 pages)
Sharp R-190HW Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Mikrowellen Sharp R-190HW.
Wir stellen 1 PDF-Handbücher Sharp R-190HW zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Spezifikationen
Inhaltsverzeichnis
Weitere Produkte und Handbücher für Mikrowellen Sharp
| Modelle | Dokumententyp |
|---|---|
| R-450E |
Betriebsanleitung
Sharp R-450E Operating instructions [en] ,
28 Seiten
|
| R-208 |
Wartungshandbuch
Sharp R-208 Service manual,
48 Seiten
|
| R-140W |
Bedienungsanleitung
R140W-R180W-R210W-9A [EN].indd,
12 Seiten
|
| R-480C |
Bedienerhandbuch
Sharp R-480C Instruction manual,
67 Seiten
|
| R-9H58 |
Wartungshandbuch
Sharp R-9H58 Service manual,
44 Seiten
|
| R-332 |
Bedienungsanleitung
GP1F31T/R, GP1F32T/R, GP1F33TT/RR/RT, GP1C331/331A/332,
9 Seiten
|
| R-508DK |
Wartungshandbuch
Sharp R-508DK Service manual,
40 Seiten
|
| R-301F |
Betriebsanweisung
Sharp R-301F User guide,
98 Seiten
|
| R-190HK |
Wartungshandbuch
Sharp R-190HK Service manual,
12 Seiten
|
| R-9200 |
Bedienungshandbuch
Sharp R-9200 Owner`s manual,
59 Seiten
|
| R-933S |
Bedienungsanleitung
Sharp R-933S Product data [en] [fr] ,
32 Seiten
|
| R-301FK |
Wartungshandbuch
Sharp R-301FK Service manual,
40 Seiten
|
| R-323T |
Wartungshandbuch
Sharp R-323T Service manual,
107 Seiten
|
| Carousel R-408D |
Spezifikationen
Sharp Carousel R-408D Specifications,
24 Seiten
|
| R-21JC |
Wartungshandbuch
Sharp R-21JC Service manual,
12 Seiten
|
| R-215EW |
Wartungshandbuch
Sharp R-215EW Service manual,
12 Seiten
|
| R-330BW |
Wartungshandbuch
Sharp R-330BW Service manual,
44 Seiten
|
| R-231Z |
Spezifikationen
Sharp R-231Z Specifications,
24 Seiten
|
| R-508FS |
Wartungshandbuch
Sharp R-508FS Service manual [en] ,
16 Seiten
|
| R-320BK |
Wartungshandbuch
Sharp R-320BK Service manual,
16 Seiten
|
© 2020, manymanuals.com. All rights reserved. | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals